Showing results: 121 - 135 of 450 items found.
-
MC-1000 -
Martel Calibrators
The MC-1000 Process Calibrator provides high accuracy calibration, common DMM functions including read and source thermocouples, RTDs, Ohms, current, pressure, frequency and test continuity. This single calibration instrument will calibrate virtually any process device including: read and source thermocouples, RTDs, Ohms, Voltage, Current, Frequency, Pressure, and test continuity.
-
YAVAP955 -
6TL Engineering
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
ZERA GmbH
While testing of meter installations on-site often a sufficient load is missing to achieve reliable results. You can generate currents up to 120 A and voltages up to 500 V with our sources.
-
Morris Products Inc.
AC Voltage: 10/50/250/500VDC Voltage: 2.5/10/50/250/500VDC Current: 500u/10m/250mAVoltage Multimeter Resistance: 2K/200K Ohms MaxBattery Test 1.5V & 9VOverload ProtectionPower Source: One AA (1.5V) BatteryVoltage Multimeter Dimensions: 2.5” X 4.0” X 1.25”Weight: 3.4 oz.
-
DCS025 -
Teledyne LeCroy
The DCS025 Deskew Calibration Source generates time-aligned voltage and current pulses for precise deskew of voltage and current probes.This is critical for measurements in which small propagation delay differences between probes can have a large impact on a calculated measurement, e.g., instantaneous power semiconductor device loss measurements.
-
Thermal Engineering Associates, Inc.
Systems for determining relationship between temperature-sensing junction voltage versus junction temperature of diodes, integrated circuits and thermal test die. Provides internal current sources, voltage measurement to 1 mV, and temperature measurement to 0.1ºC. 16-channel capability with optional printer and serial port data output.
-
DT4 -
North Atlantic Industries
The DT4 module (the enhanced version) features 24 programmable channels for either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3 – 60 VCC source. These modules can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 (Enhanced Version) are listed below.
-
CZ20074 -
Aegis Pty. Ltd.
The Aegis adjustable sensitivity AC Voltage Detector is the only tool you need to test AC voltage. About the size of a marking pen, this battery operated, non-contact tester detects AC voltages from 50 - 1000V. It's easy to operate, with flashing LED indicators, an audible buzzer and vibration to alert the user when the AC voltage has been detected. The unit will glow green when safe, and when voltage is detected it will flash red and beep at an increasing rate as you get closer to the voltage source.
-
YAV90096 -
6TL Engineering
Selectable voltage and current, comparation and measurement Drive sink or source up to 32 mA per channel Maximum voltage in output selectable from 9 to 24 VDC Possibility to use I7Os in parallel Pin voltage comparator with logic readout at fix +4VDC 10-bit resolution pin voltage measurement with CAN bus value readout Build-in editable test steps sequence (test script) Size: form G
-
Acopian Technical Company
These modular High Voltage supplies may be used as constant voltage or constant current sources. They may be remotely programmed by means of either voltage or resistance, and have provisions for remote monitoring and output inhibiting. All control and monitoring connections are on a pluggable terminal block that functions as a connector, providing wiring convenience and permitting easy and rapid connect/disconnect. Outputs are arc/short circuit protected.
-
APCI-3300-4 -
TEAM SOLUTIONS, INC.
*4 channels for the acquisition of strain gauges*4 onboard voltage sources*18-bit resolution*Optical isolation 1000 V*Software linearisation*Direct connection of the pressure sensors with terminal board PX3200
-
ResTest -
Jandel Engineering Limited
The new Jandel ResTest Test Unit is a constant current source and digital voltmeter with large colour screen, supplying constant currents between 1uA and 10mA, and measuring voltages from 0.04mV to 4000mV.
-
Playing With Fusion Inc
A power supply is an electrical device that supplies electric power to an electrical load. The main purpose of a power supply is to convert electric current from a source to the correct voltage, current, and frequency to power the load.
-
Toellner Electronic Instrumente GmbH
A power supply is an electrical device that supplies electric power to an electrical load. The main purpose of a power supply is to convert electric current from a source to the correct voltage, current, and frequency to power the load.
-
The Motwane Manufacturing Company
For decades, Motwane Voltage Detector has been a standard for international quality and safety ratings. Voltage detectors are used to signal the presence of voltage in a conductor since they make visible what we normally can’t see. Its application lies mainly in safety reasons during research, or when a service operation is under way. Most of the time, the monitored conductors come from low impedance sources whose voltage and energies are considered life-threatening.